DIY Guides

How to Reset a Tripped Circuit Breaker

Updated 2026-03-10

How to Reset a Tripped Circuit Breaker

Always verify contractor licensing and insurance in your state. Cost estimates are averages and may vary by location.

When part of your home suddenly loses power, a tripped circuit breaker is the most likely cause. Resetting a breaker is a straightforward process, but understanding why it tripped matters more than flipping it back on. A breaker that trips repeatedly is telling you something important about your electrical system, and ignoring that signal can create a fire hazard.

Why Circuit Breakers Trip

A circuit breaker is a safety device. It cuts power when it detects a problem. There are three main reasons a breaker trips:

1. Circuit Overload

This is the most common cause. It happens when the total electrical draw on a circuit exceeds the breaker’s rated amperage. Running a space heater, hair dryer, and microwave on the same circuit will overload a standard 15-amp breaker.

Signs: Power loss in a specific area of the house, typically after turning on an appliance.

2. Short Circuit

A short circuit occurs when a hot wire touches a neutral wire or another hot wire. This creates a surge of current that the breaker immediately interrupts. Short circuits are more serious than overloads.

Signs: A breaker that trips immediately when reset, a burning smell near an outlet, or discolored outlet covers.

3. Ground Fault

A ground fault happens when a hot wire contacts a ground wire or a grounded surface like a metal box. Ground faults are especially dangerous in wet areas like kitchens, bathrooms, and outdoor circuits.

Signs: A GFCI outlet that has tripped (look for outlets with “Test” and “Reset” buttons in bathrooms and kitchens), or a GFCI breaker that trips in the panel.

How to Identify Which Breaker Tripped

  1. Go to your electrical panel (usually in the basement, garage, or utility closet).
  2. Open the panel door.
  3. Look for a breaker that is in the middle position — not fully ON and not fully OFF. A tripped breaker often shows a small orange or red indicator, or the toggle sits between the ON and OFF positions.
  4. If your panel is labeled, note which area of the house the breaker controls.

Step-by-Step Reset Process

Safety first: Stand on a dry surface. If the area around the panel is wet, do not touch the panel — call an electrician.

  1. Turn off or unplug all devices and lights on the affected circuit. This prevents a surge when you restore power.
  2. Push the tripped breaker toggle firmly to the full OFF position. You should feel a click.
  3. Pause for five seconds.
  4. Push the toggle firmly to the ON position. You should feel and hear a solid click.
  5. If the breaker holds, turn on devices one at a time to identify what caused the overload.
  6. If the breaker trips again immediately, do not keep resetting it. Move to the troubleshooting section below.

What to Do if the Breaker Keeps Tripping

A breaker that trips repeatedly indicates a problem that will not fix itself:

  • Trips when you plug in a specific appliance: The appliance is faulty. Stop using it and have it inspected or replaced.
  • Trips with nothing plugged in: A wiring issue exists in the circuit — likely a short or ground fault in a wire, outlet, or junction box.
  • Trips immediately on reset every time: This strongly suggests a short circuit. Do not keep resetting. Call an electrician.
  • GFCI breaker or outlet trips: Press the “Reset” button on the outlet first. If it will not hold, moisture or a ground fault is present.

When This Indicates a Serious Problem

Certain signs mean you should stop troubleshooting and call a licensed electrician immediately:

  • You smell burning or see scorch marks near the panel, outlets, or switches.
  • The breaker feels hot to the touch.
  • You hear buzzing, crackling, or sizzling from the panel.
  • The breaker toggle is physically damaged or will not stay in any position.
  • Multiple breakers trip at the same time.
  • Your home has a Federal Pacific or Zinsco panel (these brands have known safety defects).

An electrician visit for a tripping breaker typically costs $150 to $400. See Home Repair Cost Estimator (Interactive Calculator) for more pricing information.

Safety Warnings

  • Never remove the panel cover (the inner “dead front” behind the breaker toggles). Live bus bars behind it carry lethal voltage.
  • Never use a higher-amperage breaker to stop tripping. The breaker is sized to protect the wiring. Oversizing it creates a fire risk.
  • If you are uncomfortable working around your electrical panel, call a professional. There is no shame in prioritizing safety.

Key Takeaways

  • A tripped breaker is a safety mechanism doing its job — always investigate the cause before resetting.
  • Overloads are the most common and least dangerous cause. Redistribute appliances across circuits to prevent recurrence.
  • Short circuits and ground faults are more serious and often require professional diagnosis.
  • Never ignore a breaker that trips repeatedly — it is warning you about a potential fire hazard.

Next Steps